收藏本站
3.1.3.3
Sync Pulse Pulldown Enable Bit (SYNC_PD)
The sync pulse pulldown enable bit selects if the sync pulse pulldown is enabled once a sync pulse is detected. Reference
Section 4.2.1.2 for more information regarding the sync pulse pulldown.
SYNC_PD
0
1
Sync Pulse Pulldown
Disabled
Enabled
If Daisy Chain Mode is enabled, the Sync Pulse Pulldown is enabled as listed below:
SYNC_PD
0
1
1
1
1
Daisy Chain Address
Programmed
x
No
Yes
Yes
Yes
“Run Mode”
Command Received
x
x
No
Yes
Yes
Daisy Chain Address = ‘001’
x
x
x
No
Yes
Sync Pulse Pulldown
Disabled
Enabled
Disabled
Disabled
Enabled
3.1.3.4
Latency Selection Bit (LATENCY)
The latency selection bit selects between one of two data latency methods to accommodate synchronized sampling or simul-
taneous sampling. Reference Section 4.5 for more information regarding latency and data synchronization.
Latency
0
1
Data Latency
Simultaneous Sampling Mode (Latency relative to Sync Pulse)
Synchronous Sampling Mode (Latency relative to Time Slot)
3.1.3.5
Data Size Selection Bit (DATASIZE)
The data size selection bit selects one of two data lengths for the PSI5 response message as shown below.
DATASIZE
0
1
Data Length
10 Bits
8 Bits
3.1.3.6
PSI5 Sync Pulse Blanking Time Selection Bit (BLANKTIME)
The PSI5 sync pulse blanking time selection bit selects the timing for ignoring sync pulses after successful reception of a sync
pulse. Reference Section 4.2.1.1 for details regarding sync pulse detection and blanking.
BLANKTIME
0
1
Blanking Time Method
Maximum of t SYNC_OFF_500 or Response Transmission Complete
Blanking Time determined by end of response transmission for programmed time slot
3.1.3.7
PSI5 Response Message Error Detection Selection Bit (P_CRC)
The PSI5 response message error detection selection bit selects either even parity, or a 3-Bit CRC for error detection of the
PSI5 response message. Reference Section 4.3.3 for details regarding response message error detection.
P_CRC
0
1
Parity or CRC
Parity
CRC
Note: The PSI5 specification recommends parity for data lengths of 10 bits or less.
MMA52xxKW
Sensors
14
Freescale Semiconductor, Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MMA6331LT SENSORS ACCELEROMETER 14LGA
MMA6341LT IC ACCELER 3G/8G XY-AXIS 14LGA
MMA6361LT IC ACCELER 1.5G XY-AXIS 14LGA
MMA6527KW IC ACCELEROMETER XY AXIS 16QFN
MMA6556KW IC ACCELEROMETER X AXIS 16QFN
MMA6826AKW IC ACCELEROMETER XY AXIS 16QFN
MMA6854KW IC ACCELEROMETER X AXIS 16QFN
MMA7331LR2 ACCELEROMETER 4G XYZ ENH 14-LGA
相关代理商/技术参数
MMA52XXAKW 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Xtrinsic MMA52xxAKW PSI5 Inertial Sensor
MMA52XXKW 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PSI5 Inertial Sensor
MMA52XXWR2 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:PSI5 Inertial Sensor
MMA621010AEG 功能描述:加速计 - 板上安装 100/100G XY ANALOG RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA621010AEGR2 功能描述:加速计 - 板上安装 100/100G XY ANALOG RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA621010AKEG 功能描述:加速计 - 板上安装 100/100G XY ANALOG RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA621010AKEGR2 功能描述:加速计 - 板上安装 100/100G XY ANALOG RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C
MMA621010EG 功能描述:加速计 - 板上安装 100 /100 XY DIGITAL RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C